This chapter describes QLLC Layer (over X25) Messages messages. For information on message content and how to use the message, refer to the Introduction.
| QLLC.001 |
Level: C-INFO
Short Syntax: QLLC.001 reset pkt rcvd: nt cep st lcn ev
Long Syntax: QLLC.001 reset pkt rcvd: network cep state lcn event
Description: reset pkt rcvd.
| QLLC.002 |
Level: C-INFO
Short Syntax: QLLC.002 reset cnf pkt rcvd: nt cep st lcn ev
Long Syntax: QLLC.002 reset cnf pkt rcvd: network cep state lcn event
Description: reset cnf pkt rcvd.
| QLLC.003 |
Level: C-INFO
Short Syntax: QLLC.003 ckt busy cleared: nt cep st lcn ev
Long Syntax: QLLC.003 ckt busy cleared: network cep state lcn event
Description: ckt busy cleared.
| QLLC.004 |
Level: C-INFO
Short Syntax: QLLC.004 ckt busy establish: nt cep st lcn ev
Long Syntax: QLLC.004 ckt busy establish: network cep state lcn event
Description: ckt busy establish.
| QLLC.005 |
Level: C-INFO
Short Syntax: QLLC.005 QTEST_RSP timeout exceeded: nt cep st lcn ev
Long Syntax: QLLC.005 QTEST_RSP timeout exceeded: network cep state lcn event
Description: QTEST_RSP timeout exceeded check check .
| QLLC.006 |
Level: C-INFO
Short Syntax: QLLC.006 QXID_RSP timeout exceeded: nt cep st lcn ev
Long Syntax: QLLC.006 QXID_RSP timeout exceeded: network cep state lcn event
Description: QXID_RSP timeout exceeded.
| QLLC.007 |
Level: C-INFO
Short Syntax: QLLC.007 QDISCONTACT timeout exceeded: nt cep st lcn ev
Long Syntax: QLLC.007 QDISCONTACT timeout exceeded: network cep state lcn event
Description: QDISCONTACT timeout exceeded.
| QLLC.008 |
Level: C-INFO
Short Syntax: QLLC.008 QCONTACT timeout exceeded: nt cep st lcn ev
Long Syntax: QLLC.008 QCONTACT timeout exceeded: network cep state lcn event
Description: QCONTACT timeout exceeded.
| QLLC.009 |
Level: C-INFO
Short Syntax: QLLC.009 PVC CIRCUIT ACTIVE: nt cep st lcn ev
Long Syntax: QLLC.009 PVC CIRCUIT ACTIVE: network cep state lcn event
Description: PVC CIRCUIT ACTIVE. check check cep->port->hp_handle may be useful.
| QLLC.010 |
Level: C-INFO
Short Syntax: QLLC.010 PLC changed to down: nt cep st lcn ev
Long Syntax: QLLC.010 PLC changed to down: network cep state lcn event
Description: PLC changed to down.
| QLLC.011 |
Level: C-INFO
Short Syntax: QLLC.011 Q_CONTACT_RCV: nt cep st lcn ev
Long Syntax: QLLC.011 Q_CONTACT_RCV: network cep state lcn event
Description: Q_CONTACT_RCV.
| QLLC.012 |
Level: C-INFO
Short Syntax: QLLC.012 Q_EXCPTN - UNEXP_CFIELD_RCVD: nt cep st lcn ev
Long Syntax: QLLC.012 Q_EXCPTN - UNEXP_CFIELD_RCVD: network cep state lcn event
Description: Q_EXCPTN - UNEXP_CFIELD_RCVD.
| QLLC.013 |
Level: C-INFO
Short Syntax: QLLC.013 Q_CONTACT_CNF: nt cep st lcn ev
Long Syntax: QLLC.013 Q_CONTACT_CNF: network cep state lcn event
Description: Q_CONTACT_CNF.
| QLLC.014 |
Level: C-INFO
Short Syntax: QLLC.014 Q_DISCONTACT_RCV: nt cep st lcn ev
Long Syntax: QLLC.014 Q_DISCONTACT_RCV: network cep state lcn event
Description: Q_DISCONTACT_RCV.
| QLLC.015 |
Level: C-INFO
Short Syntax: QLLC.015 Q_DISCONTACT_CNF: nt cep st lcn ev
Long Syntax: QLLC.015 Q_DISCONTACT_CNF: network cep state lcn event
Description: Q_DISCONTACT_CNF.
| QLLC.016 |
Level: C-INFO
Short Syntax: QLLC.016 Q_CIRCUIT_BUSY: nt cep st lcn ev
Long Syntax: QLLC.016 Q_CIRCUIT_BUSY: network cep state lcn event
Description: Q_CIRCUIT_BUSY.
| QLLC.017 |
Level: C-INFO
Short Syntax: QLLC.017 Q_XID_CMD_RCV: nt cep st lcn ev
Long Syntax: QLLC.017 Q_XID_CMD_RCV: network cep state lcn event
Description: Q_XID_CMD_RCV.
| QLLC.018 |
Level: C-INFO
Short Syntax: QLLC.018 Q_XID_RSP_RCV: nt cep st lcn ev
Long Syntax: QLLC.018 Q_XID_RSP_RCV: network cep state lcn event
Description: Q_XID_RSP_RCV.
| QLLC.019 |
Level: C-INFO
Short Syntax: QLLC.019 b001 plc chg to dwn. nt
Long Syntax: QLLC.019 b001 plc change to down network
Description: b001 plc change to down.
| QLLC.020 |
Level: C-INFO
Short Syntax: QLLC.020 b002 plc ckt bsy chg: nt cep lcn cst st
Long Syntax: QLLC.020 b002 plc ckt busy change: network cep for lcn cep state state
Description: b002 plc ckt busy change.
| QLLC.021 |
Level: C-INFO
Short Syntax: QLLC.021 b003 clear_reset pkt rcvd: nt cep lcn cst st
Long Syntax: QLLC.021 b003 clear_reset pkt rcvd: network cep lcn cep state state
Description: b003 clear_reset pkt rcvd.
| QLLC.022 |
Level: C-INFO
Short Syntax: QLLC.022 b004 q_pkt rcvd: nt qa_field lcn cst qa-field
Long Syntax: QLLC.022 b004 q_pkt rcvd: network qa_field lcn cep state qa_field
Description: b004 q_pkt rcvd.
| QLLC.023 |
Level: C-INFO
Short Syntax: QLLC.023 b004 q_pkt rcvd: nt qc_field lcn cst qc-field
Long Syntax: QLLC.023 b004 q_pkt rcvd: network qc_field lcn cep state qc_field
Description: c_field.
| QLLC.024 |
Level: C-INFO
Short Syntax: QLLC.024 b004 user data pkt rcvd: nt cep lcn st
Long Syntax: QLLC.024 b004 user data pkt rcvd: network cep lcn state
Description: b004 user data pkt rcvd.
| QLLC.025 |
Level: C-INFO
Short Syntax: QLLC.025 b005 ckt active: nt cep lcn st
Long Syntax: QLLC.025 b005 ckt active: network cep lcn state
Description: b005 ckt active.
| QLLC.026 |
Level: C-INFO
Short Syntax: QLLC.026 b006 plc change to up: nt
Long Syntax: QLLC.026 b006 plc change to up: network
Description: b006 plc change to up.
| QLLC.027 |
Level: C-INFO
Short Syntax: QLLC.027 b019 link busy change: nt link_status lnk stat
Long Syntax: QLLC.027 b019 link busy change: network link_status link status
Description: b019 link busy change.
| QLLC.028 |
Level: C-INFO
Short Syntax: QLLC.028 b020 Rx Incoming call: nt peer lcn st
Long Syntax: QLLC.028 b020 Rx Incoming call: nt peer lcn st
Description: b020 Rx Incoming call.
| QLLC.029 |
Level: C-INFO
Short Syntax: QLLC.029 b022 get qdata: nt peer lcn st tsk
Long Syntax: QLLC.029 b022_get_qdata_pkt: network peer lcn state transmit task
Description: b019 Rxk call connected.
| QLLC.030 |
Level: C-INFO
Short Syntax: QLLC.030 b023 rcv pkt: nt tx_task lcn st
Long Syntax: QLLC.030 b023_rcv_pkt_state_dr : network tx_task lcn state
Description: b023 receive packet state DR
| QLLC.031 |
Level: C-INFO
Short Syntax: QLLC.031 b023 pkt rcvd state DR: nt tx_task lcn st
Long Syntax: QLLC.031 b023 pkt rcvd state DR: network tx_task lcn state
Description: b023 pkt rcvd state DR.
| QLLC.032 |
Level: C-INFO
Short Syntax: QLLC.032 b024 crt rst or clr pkt: nt cep lcn st code
Long Syntax: QLLC.032 b024 create reset or clear pkt: network cep lcn state code
Description: b024 create reset or clear pkt.
| QLLC.033 |
Level: C-INFO
Short Syntax: QLLC.033 s003 open port: nt prtcl prtcl
Long Syntax: QLLC.033 s003 open port: network prtcl protocol
Description: s003 open port: protocol.
| QLLC.034 |
Level: C-INFO
Short Syntax: QLLC.034 s003 close port: nt protocol prtcl
Long Syntax: QLLC.034 s003 close port: network protocol protocol
Description: s003 close port.
| QLLC.035 |
Level: C-INFO
Short Syntax: QLLC.035 s005 register station: nt lcn prtcl lcn hndl
Long Syntax: QLLC.035 s005 register station: network lcn protocol lcn handle
Description: s005 register station.
| QLLC.036 |
Level: C-INFO
Short Syntax: QLLC.036 s006 unregister station: nt cep lcn
Long Syntax: QLLC.036 s006 unregister station: network cep lcn
Description: s006 unregister station.
| QLLC.037 |
Level: C-INFO
Short Syntax: QLLC.037 s007 call req: nt cep prtcl
Long Syntax: QLLC.037 s007 call req: network cep protocol
Description: s007 call request
| QLLC.038 |
Level: C-INFO
Short Syntax: QLLC.038 s008 clr call req: nt cep lcn code
Long Syntax: QLLC.038 s008 clr call req: network cep lcn code
Description: s011 data request prim.
| QLLC.039 |
Level: C-INFO
Short Syntax: QLLC.039 s009 xid req: nt cep lcn state
Long Syntax: QLLC.039 s009 xid request : network cep lcn cep state :
Description: s009 xid request prim.
| QLLC.040 |
Level: C-INFO
Short Syntax: QLLC.040 s011 data req: nt cep lcn state
Long Syntax: QLLC.040 s011 data req: network cep lcn cep state
Description: s011 data request prim
| QLLC.041 |
Level: C-INFO
Short Syntax: QLLC.041 s012 xid resp: nt cep lcn modifier
Long Syntax: QLLC.041 s012 xid response : nt cep lcn modifier
Description: s017 q_rsp timer expired.
| QLLC.042 |
Level: C-INFO
Short Syntax: QLLC.042 s013 tst resp: nt cep lcn state modifier
Long Syntax: QLLC.042 s013 tst resp: nt cep lcn state modifier
Description: s013 test response
| QLLC.043 |
Level: C-INFO
Short Syntax: QLLC.043 s016 ckt bsy req: nt cep lcn state modifier
Long Syntax: QLLC.043 s016 ckt bsy req: nt cep lcn state modifier
Description: s016 circuit busy request
| QLLC.044 |
Level: C-INFO
Short Syntax: QLLC.044 s017 rsp tmr expr: nt cep lcn state
Long Syntax: QLLC.044 s017 q response timer expired: network cep lcn state
Description: s022 contact request prim.
| QLLC.045 |
Level: C-INFO
Short Syntax: QLLC.045 s018 set stn role: nt cep lcn state modifier
Long Syntax: QLLC.045 s018 set station role : network cep lcn state modifier
Description: s018 set station role
| QLLC.046 |
Level: C-INFO
Short Syntax: QLLC.046 s019 inc call resp: nt cep lcn hnd modifier
Long Syntax: QLLC.046 s019 incoming call response: network cep lcn handle modifier
Description: s019 incoming call response
| QLLC.047 |
Level: C-INFO
Short Syntax: QLLC.047 s029 rst req: nt cep lcn state modifier
Long Syntax: QLLC.047 s029 reset request: network cep lcn state modifier
Description: s029 reset request
| QLLC.048 |
Level: C-INFO
Short Syntax: QLLC.048 s022 cont req: nt cep lcn state
Long Syntax: QLLC.048 s022 contact request: network cep lcn state
Description: s022 contact request
| QLLC.049 |
Level: C-INFO
Short Syntax: QLLC.049 s023 cont resp: nt cep lcn state modifier
Long Syntax: QLLC.049 s023 contact response: network cep lcn state modifier
Description: s023 contact response.
| QLLC.050 |
Level: C-INFO
Short Syntax: QLLC.050 s024 disc req prim: nt cep lcn state
Long Syntax: QLLC.050 s024 discontact request prim: nt cep lcn state
Description: s024 discontact request prim.
| QLLC.051 |
Level: C-INFO
Short Syntax: QLLC.051 s025 disc resp prim: nt cep lcn state
Long Syntax: QLLC.051 s025 discontact response prim: nt cep lcn state
Description: s025 discontact response prim.
| QLLC.052 |
Level: C-INFO
Short Syntax: QLLC.052 s027 strt q_rsp tmr: nt cep lcn state
Long Syntax: QLLC.052 start q_rsp timer: network cep lcn state
Description: start q_rsp timer.
| QLLC.053 |
Level: C-INFO
Short Syntax: QLLC.053 s028 chg hnd prim: nt cep lcn state hndl
Long Syntax: QLLC.053 s028 change handle prim: network cep lcn state h_handle
Description: s028 change handle prim.
| QLLC.054 |
Level: C-INFO
Short Syntax: QLLC.054 s029 abort call: nt cep lcn state
Long Syntax: QLLC.054 s029 abort call: network cep lcn state
Description: s029 abort call.